]> The Johns Hopkins University Applied Physics Laboratory

11100 Johns Hopkins Rd. Laurel MD 20723 United States of America brian.sipos+ietf@gmail.com

Transport Delay-Tolerant Networking DTN PKIX This document extends the Bundle Protocol Endpoint ID (EID) concept into an EID Pattern, which is used to categorize any EID as matching a specific pattern or not. EID Patterns are suitable for expressing configuration, for being used on-the-wire by protocols, and for being easily understandable by a layperson. EID Patterns include scheme-specific optimizations for expressing set membership and each scheme pattern includes text and binary encoding forms; the pattern for the "ipn" EID scheme being designed to be highly compressible in its binary form. This document also defines a Public Key Infrastructure Using X.509 (PKIX) Other Name form to contain an EID Pattern and a handling rule to use a pattern to match an EID.

Introduction The Bundle Protocol (BP) Version 7 specification of defines Uniform Resource Identifier (URI) text and Concise Binary Object Representation (CBOR) binary encoding forms of an Endpoint ID (EID). The EID is used as both a source and a destination for individual bundles as well as a destination for status reports. In addition to the base protocol, the BP Security specification of uses EIDs as security sources and the TCP Convergence Layer (TCPCL) of uses EIDs for peer identification. BP Agent implementations have necessarily used methods of defining patterns for matching multiple EIDs in order to configure routing, forwarding, and delivery of bundles, security policy, and convergence layer policy, but these have not yet been standardized and do not have a concise form suitable for on-the-wire messaging. In much the same way that the Classless Inter-domain Routing (CIDR) mechanism of can be used to aggregate a contiguous and bit-aligned block of IP addresses in a concise unit (encoded as text or otherwise), this concept of EID Pattern is used to aggregate a set of EIDs into a single concise unit. This is valuable because an EID includes both an identifier of the node sending or receiving the bundle as well as an identifier for the specific service which generated or will process the bundle. Any EID Pattern can be used both to aggregate EIDs based on node identifier, service identifier, or both. A purely text-based pattern mechanism such as could handle the general case of matching the text form of EIDs (as URIs) but would not be able to achieve the same level of encoding compression and would not be able to express of exact numeric ranges like the scheme-specific mechanism defined in this document. The certificate profile and NODE-ID definition of uses the text form of EID to authenticate nodes based on EID. This document defines a Public Key Infrastructure Using X.509 (PKIX) Other Name Form to contain an EID Pattern and a handling rule to use a pattern to match an EID. This allows authenticating an individual EID based on an EID Pattern in much the same way as using a "wildcard" certificate to match a DNS name (see ).

Goals The text form of an EID Pattern defined in is not a URI and is not bound by the character set restrictions imposed in . This is much the same as a URI template is also not itself a URI. Although some forms of EID Pattern can contain reserved URI characters, it is not guaranteed that any particular EID Pattern will be intrinsically differentiable from an EID. See for details on handling concerns. For the pattern forms defined in , the exact-match pattern's text form is identical with its matching EID (with explicitly stated limitations). This behavior is not required or strictly necessary but is a convenient side effect of the text definitions and makes the EID Pattern a proper superset of EID. Because of its structure, used to simplify processing, the CBOR form for EID Pattern will never be identical to or a superset of EID. One other aspect of this patterning mechanism is that the text form of each scheme-specific pattern is intended to be, in a subjective sense, natural and understandable for the case of a human manually typing patterns into a text document or quick email message; the interpretation of the text pattern needs to "make sense" with minimal training. In summary, current and new scheme-specific EID Pattern definitions SHALL specify all of the following:

• A logical information model for the scheme-specific pattern.
• Any exceptions or qualifications to the goal of text-form EID being an identity EID Pattern (i.e., a text EID will act as a pattern unmodified, and that pattern will match only the original EID).
• Logic for matching a specific EID against the information model.
• Logic for performing set operations with the information model (i.e., pattern unions, intersections, and subset comparisons).
• Both text-form and CBOR-form encodings for those scheme-specific information models.

Scope This document defines a logical model of pattern matching BP Endpoint IDs and both text and CBOR encoding forms, as well as PKIX extensions to make use of EID Patterns in a public key certificate (PKC). This document does not define a method of disambiguating an EID from an EID Pattern (in either encoded form) without any other context. Given a pure text or CBOR encoding of an arbitrary value, there needs to be some external context to determine how to interpret it. This document defines scheme-specific pattern for the "ipn" URI scheme, as its semantics are well-established, while the other currently registered "dtn" scheme lacks well-defined semantics for the structure of its authority component (which would be necessary for wildcard logic). Although the same EID definitions apply to BP Version 6 this document does not provide any mechanisms of integrating with that protocol. It is an implementation matter for a BP Agent to use EID Patterns with BP Version 6 bundles and their compressed bundle header encoding (CBHE).

Use of ABNF This document defines text structure using the Augmented Backus-Naur Form (ABNF) of . The entire ABNF structure can be extracted from the XML version of this document using the XPath expression: '//sourcecode[@type="abnf"]' The following initial fragment defines the top-level rules of this document's ABNF. ; Shared wildcard rules wildcard = "*" multi-wildcard = "**" non-zero-decimal = (%x31-39 *DIGIT) From the document the definition is taken for pchar and scheme. From the document the definition is taken for digit. From the document the definition is taken for nbr-delim.

Use of CDDL This document defines CBOR structure using the Concise Data Definition Language (CDDL) of . The entire CDDL structure can be extracted from the XML version of this document using the XPath expression: '//sourcecode[@type="cddl"]' The following initial fragment defines the top-level rules of this document's CDDL, which includes the example CBOR content. start = eid-pattern / embed-eid-pattern From the document the definition is taken for eid-structure.

Terminology The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 when, and only when, they appear in all capitals, as shown here. The terms "Endpoint" and "Endpoint ID" in this document refer to the meanings defined in .

Patterns for BP Endpoint IDs This document does not define a universal form of EID Pattern, though text forms of EID Patterns do share concepts and rules for wildcard matching (e.g., ). Instead, in order to achieve efficiencies in non-text encoding, each EID scheme uses a different form of complex pattern matching. There are also scheme-independent match-all forms that function without a processor needing scheme-specific logic for all possible schemes. An EID Pattern processor MAY normalize the internal representation of a pattern to an equivalent one without keeping track of the original pattern information or encoding. If an pattern-using application needs to ensure that original encodings are kept, that needs to happen outside of the pattern processor. See for recommendations about this need.

Pattern Set and Pattern Items The overall concept of this patterning structure is that one "EID Pattern" can be used to match any combination of EIDs. This is accomplished by a single pattern being composed of independent pattern items, each with scheme-specific rules and syntax. The conceptual model of the EID Pattern is as a non-empty sequence of scheme-specific pattern items. This sequence is ordered in order to make translating between forms deterministic, as each encoding form necessarily has a specific order of items. Although the encoding forms are necessarily ordered, the matching logic for an EID Pattern is independent of the order of its items. An EID pattern SHALL be considered to match an EID if any of its constituent items match the EID. Because matching against an "any-scheme" item (see ) will necessarily make any scheme-specific patterns redundant, the text and CBOR forms of the EID pattern have a compressed form of any-scheme matching and disallow combining the any-scheme pattern with other items. The text form of the EID pattern is the following, which uses the URI reserved character "|" to delimit items in the sequence. Because the delimiter is used between items, an EID pattern with one item has an identical text form to that item. This correspondence in text form between a single EID and an EID pattern item which matches that single EID SHALL be enforced by any future scheme-specific pattern syntax registered with IANA. eid-pattern = any-scheme-item / eid-pattern-set eid-pattern-set = eid-pattern-item *( "|" eid-pattern-item ) eid-pattern-item = scheme-pat-item / any-ssp-item ; Extension point at scheme-pat-item for future scheme-specific rules scheme-pat-item = ipn-pat-item The CBOR form of the EID pattern is the following, which uses an enveloping array to contain the items. Although the any-scheme pattern includes a compressed encoding, avoiding the outer array, it still follows the conceptual model of a set of items (in which there is allowed only one item). Because there is otherwise always an outer array, there is no concept of a "bare" scheme-specific pattern item in the CBOR form and no exact correspondence in binary form between a single EID and an EID pattern item which matches that single EID. eid-pattern = any-scheme-item / eid-pattern-set eid-pattern-set = [1* eid-pattern-item] eid-pattern-item = scheme-pat-item / any-ssp-item ; Each pattern still follows eid-structure scheme-pat-item = $eid-pat-item .within eid-structure

Any-Scheme Pattern Item The simplest pattern item is one which will match any EID of any URI scheme. Because this necessarily disallows scheme-specific logic, the any-scheme pattern has only its identity with no parameters or conceptual structure. When the any-scheme item is present in an EID pattern, it SHALL be the only item in the pattern. Any other, scheme-specific items would be redundant and unnecessary when combined with the any-scheme item. The text form of the any-scheme pattern is the following ABNF which matches only the exact text *:**. As defined in , when this text form is present it cannot be combined with other items. any-scheme-item = wildcard ":" multi-wildcard The CBOR form of the any-scheme pattern is the following CDDL which matches only the exact value true. As defined in , when this CBOR form is present it occurs outside of an enveloping array and thus cannot be combined with other items. any-scheme-item = true

Any-SSP Pattern Item The next most generic pattern item is one which will match any SSP within a specific URI scheme. This includes schemes known to the EID handler as well as schemes by enumerated integer that need not be understood by the EID handler. When an any-SSP item is present in an EID pattern, it SHALL be the only item for the associated scheme. Any other, scheme-specific items would be redundant and unnecessary when combined with the any-SSP item for that same scheme. The text form of the any-SSP pattern is the following ABNF, where the scheme part can either be a proper URI scheme or a positive integer value (valid values are restricted by the scheme registry ). any-ssp-item = (scheme / non-zero-decimal) ":" multi-wildcard The CBOR form of the any-SSP pattern is the following CDDL. Because this does not match the eid-structure rule, it is guaranteed to be disambiguated with any current or future scheme-specific $eid-pat-item socket uses. any-ssp-item = (uint .gt 0) / tstr

EID Matching An any-SSP pattern SHALL be considered to match a specific EID when both have the same normalized scheme. Scheme normalization for text EIDs is to convert to a lower-case alphabetic form in accordance with . For schemes which are known to the processing entity, the integer form SHALL be the normalized form. For schemes which are unknown to the processing entity, the text form of the any-SSP pattern scheme SHALL be used to match text-form EIDs and the integer form of the pattern scheme SHALL be used to match CBOR-form EIDs. This means that for entities that cannot process a specific (fictional) private-use scheme with value 65536 and name "example", the following pattern will guarantee proper handling by any entity: example:**|65536:**

IPN Scheme Pattern Item As defined in and updated in , IPN scheme EIDs have a SSP which is logically divided into three integer numeric components. Because of this, the pattern for IPN scheme EIDs is based on matching a numeric value or range for each component. For the remainder of this document, the term "IPN pattern" is used as shorthand to mean the EID pattern item used for the "ipn" scheme. An IPN pattern SHALL logically contain exactly three components corresponding to the IPN scheme EID components of:

1. Allocator Identifier
2. Node Number
3. Service Number

The conceptual model of the IPN pattern is that each of the components of the SSP can be matched as one of:

Specific value:

This will match only a single value (as decoded number).

Range:

This will match any value contained in a disjoint set of numeric intervals.

Wildcard:

This will match any valid value, but not the absence of a value.

Within a single component of the IPN pattern, the range intervals SHALL be disjoint and non-contiguous. Any overlapping or contiguity of intervals within a set can be coalesced into a single covering interval with the same meaning. The text form of a range can, but SHOULD NOT, contain overlapping or contiguous intervals. The CBOR form of a range does not allow overlapping intervals because of its compressed form, but does allow contiguous intervals. The decoder for any form of an IPN pattern SHALL normalize all intervals sets to satisfy information model requirements. The decoder for any form of an IPN pattern SHOULD treat the failure of any component of a pattern as a failure to decode the whole pattern. A limitation of this mechanism is that there is no intermediate component pattern between a specific set of finite intervals and the match-all (unbounded) wildcard. There is no capability of including an non-finite bounds within any interval. But the components of the IPN scheme itself have finite bounds so a range can be made to capture component values up to and including the EID component bound.

EID Matching An IPN pattern SHALL be considered to match a specific EID when both have the same scheme and each component of the the pattern matches the corresponding logical component of the EID SSP. If any component doesn't match, the whole pattern does not match. Each pattern component SHALL be considered to match according to the following rules:

Specific value:

The pattern component SHALL be compared to the EID component as an exact match of decoded numeric value.

Range:

The pattern component SHALL be considered to match with any EID component value that is contained in any of the finite intervals of the range.

Wildcard:

The pattern component SHALL be considered to match with any EID component.

Because these are dealing with numeric values in an information model, the matching occurs after any encoding-specific normalization (i.e. it's not a text pattern for the text encoding, the matching is performed within the information model of the SSP).

Pattern Set Logic One benefit of using an EID pattern with an information model of a sequence of numbers or ranges is that performing set logic such as intersection or containment is straightforward. For set logical behavior, the "specific value" case is treated as a singleton set and the wildcard case is treated as the unbounded-interval. Two IPN patterns are equivalent if their matching EID sets are identical. Two IPN patterns intersect if all of their corresponding components intersect, and the intersection of each component range can be readily computed using multi-interval set logic. Likewise, one IPN pattern is a subset (or proper subset) of another pattern if all of the components is a subset (or proper subset) of the other's corresponding component.

Text Form The text form of the IPN pattern conforms to the ABNF in , which is a superset of the IPN scheme itself as defined in but with a different structure. Each component is separated by the same character "." as in the IPN URI scheme. This pattern uses reserved URI characters of "[" and "]" (see ) to indicate the presence of a range set for a component, the character "," to separate the intervals of a range, the character "-" to indicate an interval within the set, and the character "+" to indicate a half-open interval. The enveloping characters "[" and "]" SHALL indicate the presence of a range of possible values for that component. The logical structure and ABNF below disallows the possibility of nested ranges. Within each range, the character "," SHALL separate multiple numeric intervals within the range. The presence of a completely empty interval (e.g., "[]" or "[,3]") is disallowed by the ABNF below and SHALL be treated as invalid. If an interval contains a single numeric value it SHALL be treated is a length-one range. If an interval contains two numeric values separated by a "-" character, the interval SHALL be treated as inclusive of both values. The lower bound of the interval is expected be on the left side of the "-" separator, but decoders SHALL handle both possible orderings of interval bounds. If an interval contains a single numeric value followed by the half-open "+" character it SHALL be treated as having the lower bound of that value and the upper bound as the largest value for that component.

IPN Pattern ABNF Schema ipn-pat-item = "ipn:" (ipn-ssp3 / ipn-ssp2) ; Separate allocator and node numbers ipn-ssp3 = ipn-part-pat nbr-delim ipn-part-pat nbr-delim ipn-part-pat ; First component is the qualified node number ipn-ssp2 = ("!" / ipn-part-pat) nbr-delim ipn-part-pat ; Each component in the pattern ipn-part-pat = ipn-decimal / ipn-range / wildcard ; Same normalized form as IPN scheme itself ipn-decimal = "0" / non-zero-decimal ipn-range = "[" ipn-interval *( "," ipn-interval ) "]" ipn-interval = ipn-decimal [ ("-" ipn-decimal) / "+" ]

When decoding a two-component IPN pattern, the first component SHALL be treated as a fully-qualified node number (FQNN) in accordance with and decomposed into separate allocator and node number components. When decoding a two-component IPN pattern, the first-component text "!" SHALL be treated as the LocalNode FQNN (0,2^32 - 1) in accordance with . When encoding an IPN pattern, the (non-range, non-wildcard) LocalNode FQNN SHOULD be detected and encoded as a two-component pattern using the "!" syntax. There can be multiple valid ways to decompose an FQNN component containing one or more intervals, and a pattern processor MAY choose any one that results in the same matching logic. When decoding, a pattern processor does not need to keep track of how many components the original pattern used; the pattern itself always has three components as defined in . The canonical text form of an IPN pattern SHALL use three components. The canonical text form SHALL NOT contain any overlapping or contiguous intervals. The canonical text form SHALL order all intervals in ascending numeric order. The canonical text form SHALL encode all intervals with the lower bound before the upper bound.

CBOR Form The CBOR form of the IPN pattern conforms to the CDDL in . Just as in the IPN URI scheme the pattern scheme identifier is 2, the first components of the SSP identify the node and the last component identifies the service. Each of the IPN pattern components SHALL be CBOR encoded as follows:

Specific value:

A number corresponding to the uint rule.

Range:

An array item corresponding to the ipn-range rule.

Wildcard:

The true item.

The wildcard sentinel values have no intrinsic meaning and were simply chosen to be one-octet-encoded special items. The encoding of ranges is a compressed form in which each pair of values in the range indicates:

1. The non-zero offset from the previous one-past-end-of-range, or the offset from zero if there is no preceding range.
2. The length of this range, which is inclusive of the first and last contained value so will always be non-zero, or the null value if the length extends to the largest value for that component.

Another way to interpret these pairs is that each number indicates the length of alternating "excluded" and "included" intervals for the range.

IPN Pattern CDDL Schema $eid-pat-item /= [ scheme-num: 2, SSP: ipn-ssp ] ipn-ssp = [ 3*3 ipn-part-pat, ] ipn-part-pat = uint / ipn-range / true ipn-range = [ 1* ipn-interval-pair ] ipn-interval-pair = ( ; only the first interval offset can be zero offset: uint, ; only the last interval length can be null length: (uint .gt 0) / null, )

PKIX Certificate Profile Update This document expands upon the PKIX profile of TCPCLv4 to allow an EID Pattern in any certificate where an Node ID is required or allowed.

New Other Name Form This document defines a PKIX Other Name Form identifier, id-on-bundleEIDPattern in ; this identifier can be used as the type-id in a Subject Alternative Name (SAN) entry of type otherName. The BundleEIDPattern value associated with the otherName type-id id-on-bundleEIDPattern SHALL be an EID Pattern text form, encoded as an UTF8String, with a scheme that is present in the IANA "Bundle Protocol URI Scheme Types" registry .

New Identifier Type This specification defines an EID-PATTERN-ID of a certificate as being the Subject Alternative Name entry of type otherName with a name form of BundleEIDPattern and a value limited to an EID Pattern text form. An entity SHALL ignore any entry of type otherName with a name form of BundleEIDPattern and a value that is some text other than an EID Pattern. The EID-PATTERN-ID is similar to the NODE-ID as defined in but can match many different and distinct Endpoint IDs. URI matching of an EID-PATTERN-ID SHALL use the scheme-specific EID matching logic defined in this specification. An EID Pattern scheme can refine this matching logic with rules regarding how Endpoint IDs within that scheme are to be compared with the issued EID-PATTERN-ID. As an augmentation of : Unless prohibited by CA policy, a TCPCL end-entity certificate SHALL contain either a NODE-ID or an EID-PATTERN-ID that authenticates the node ID of the peer. All other requirements of that certificate profile are unchanged by this document.

New Name Constraints Logic This document defines a logic for using EID Pattern(s) within the Name Constraints extension of for CA certificates. Because the EID Pattern does not define a general-purpose subset logic, a Name Constraints with an EID Pattern cannot directly constrain subordinate SANs with EID or EID Pattern items so has no effect on path validation (see ). It is instead used to constrain the ultimate identity validation (see and ) for Node IDs specifically and any future validation of EIDs more generally as defined below. As an augmentation of : When performing a validation of a Node ID against an end entity certificate with NODE-ID or EID-PATTERN-ID, the validation SHALL also validate the Node ID based on all of the CA certificates in the path which contain a Name Constraints extension itself containing an Other Name Form of id-on-bundleEIDPattern. That match SHALL consider both the permitted and excluded subtrees of the Name Constraints in accordance with . Due to the nature of matching any possible EID, a Name Constraints extension SHOULD NOT contain an BundleEIDPattern with the match-all pattern *:** as this serves no purpose. Including a match-all pattern in the included subtrees does not add any value and including it in the excluded subtrees is functionally the same thing as disallowing the presence of the id-kp-bundleSecurity Extended Key Usage. When issuing CA or end entity certificates, a CA limited by Name Constraints containing BundleEIDPattern values MAY make use of scheme-specific subset logic to determine that the combination of end entity SAN and CA Name Constraints will not validate any possible Node ID and refuse to issue the requested certificate. For example, a root CA constrained with an included subtree of ipn:0.*.* could disallow issuing a subordinate intermediate CA with a constrained included subtree of ipn:** because it isn't a proper subset of its parent constraint, or could disallow issuing an end entity certificate with a SAN identity of ipn:977000.2.3 because it is guaranteed to not pass Node ID validation. The refusal or not to issue such subordinate certificates does not affect the ultimate validation of the Node ID but does make it less likely for certificates to be used by an end entity which will never succeed at Node ID validation.

Enveloping Considerations When an EID pattern is enveloped into a data store or protocol data unit, it is important to avoid requiring the processor of that containing context to understand the nuances of EID Pattern syntax. For the text form of EID Patterns this is straightforward because the encoded text string can simply be handled without concern for its contents. The use of an EID Pattern as a PKIX Other Name Form in makes use of this strategy. For the binary form of EID Patterns, when the encoded item is not handled as a simple byte string it is RECOMMENDED to embed the EID Pattern within a CBOR byte string as a single item. This is formalized by the following CDDL. embed-eid-pattern = bstr .cbor eid-pattern Embedding in a byte string this way allows BP EID Pattern-unaware processors to handle it without concern for its syntax or validity. Using a single-item embedding ensures that the number of pattern items contained is still available to decoders in the eid-pattern array head. A similar recommendation is provided here for enveloping EIDs themselves, which is not discussed in so this document does not formally update that specification. For the binary form of EIDs, when the encoded item is not handled as a simple byte string it is RECOMMENDED to embed the EID within a CBOR byte string as a single item. This is formalized by the following CDDL. embed-eid-structure = bstr .cbor eid-structure Embedding in a byte string this way allows BP EID-unaware processors to handle it without concern for its syntax or validity. Although this adds some redundancy to the encoding because the eid-structure is always a two-element array, it is limited to the single byte of the its array head. This is also consistent with how the existing Previous Node block-type-specific data content is defined in .

Security Considerations It is critical for applications handling EIDs and EID Patterns to positively distinguish between the two based on the context in which the value is being used. For PKIX Subject Alternative Name this is distinguished by the different Other Name forms. An EID which is inappropriately interpreted as an EID Pattern could allow an attacker to elevate access depending upon other aspects of the system being accessed. CAs which issue certificates containing EID Patterns need to consider the implications of an overly-broad pattern in the same way that current Web PKI CAs manage certificates with wildcard DNS-IDs. This is discussed for DNS-IDs in . Although the reserved characters "[" and "]" are disallowed within the URI authority and path segments by there are still URI processors which could be lax about enforcing that restriction and could allow an EID pattern to be decoded in a place where an actual EID is expected. This could allow unwanted side-effects when the EID is handled by a BP Agent. The URI authority part and path segments are percent-encoded text and need to be handled by EID processors as such for both pattern matching and equality comparison. Additionally, for the IPN scheme there are numeric values that need to be handled as such for pattern matching and comparison.

IANA Considerations

Bundle Protocol URI Scheme Types This specification re-uses the "Bundle Protocol URI Scheme Types" registry within the "Bundle Protocol" registry group for the CBOR encoding of EID Patterns and adds an informative column "EID Pattern Reference" as in the following table. Specifications of new EID Pattern schemes SHALL define all of the required items from to ensure that pattern behavior is consistent across different schemes. Bundle Protocol URI Scheme Types

Value	Description	...	EID Pattern Reference
2	ipn		of [This specification]

Object Identifier for PKIX Other Name Forms IANA has created, under the "Structure of Management Information (SMI) Numbers" registry group , a registry titled "SMI Security for PKIX Other Name Forms". This other name forms table is updated to include a row for containing an Endpoint ID Pattern as in the following table. PKIX Other Name Forms

Decimal	Description	References
ON-TBA	id-on-bundleEIDPattern	[This specification]

The formal structure of the associated other name form is in . The use of this form is defined in .

C509 General Names Registry IANA has created, under the "CBOR Encoded X.509 (C509) Parameters" registry group , a registry titled "C509 General Names Registry". This general names table is updated to include a row for BP Endpoint ID Pattern with the following parameters.

Label:

-TBA2

Name:

otherName with BundleEIDPattern

Comments:

id-on-bundleEIDPattern (1.3.6.1.5.5.7.8.ON-TBA) 06 08 2B 06 01 05 05 07 08 ON-TBA

Value:

embed-eid-pattern (from [this specification])

This general names table is updated to include a row for BP Endpoint ID with the following parameters.

Label:

-TBA1

Name:

otherName with BundleEID

Comments:

id-on-bundleEID (1.3.6.1.5.5.7.8.11) 06 08 2B 06 01 05 05 07 08 0B

Value:

embed-eid-structure (from [this specification])

Both of these code points can be used in a C509 certificate to create a more concise encoding of the same Other Name value than the general form defined in which uses an OID to identify the Other Name Form and ASN.1 encoded text form of EID and EID Pattern. These code points are purely to enable smaller encodings, an EID-unaware certificate processor can still use the longer general (ASN.1) encoding of these other name forms and not lose any information. The use of these forms is defined in .

References Normative References IANA IANA IANA ITU-T ITU-T Recommendation X.680, ISO/IEC 8824-1:2015 Informative References W3C

ASN.1 Module The following ASN.1 module formally specifies the BundleEIDPattern structure and its Other Name form in the syntax of . This specification uses the ASN.1 definitions from with the 2002 ASN.1 notation used in that document. DTN-EIDPATTERN-2023 { iso(1) identified-organization(3) dod(6) internet(1) security(5) mechanisms(5) pkix(7) id-mod(0) id-mod-dtn-eidpattern-2023(MOD-TBA) } DEFINITIONS IMPLICIT TAGS ::= BEGIN IMPORTS OTHER-NAME FROM PKIX1Implicit-2009 -- [RFC5912] { iso(1) identified-organization(3) dod(6) internet(1) security(5) mechanisms(5) pkix(7) id-mod(0) id-mod-pkix1-implicit-02(59) } id-pkix FROM PKIX1Explicit-2009 -- [RFC5912] { iso(1) identified-organization(3) dod(6) internet(1) security(5) mechanisms(5) pkix(7) id-mod(0) id-mod-pkix1-explicit-02(51) } ; id-on OBJECT IDENTIFIER ::= { id-pkix 8 } DTNOtherNames OTHER-NAME ::= { on-bundleEIDPattern, ... } -- The otherName definition for Bundle EID Pattern on-bundleEIDPattern OTHER-NAME ::= { BundleEIDPattern IDENTIFIED BY { id-on-bundleEIDPattern } } id-on-bundleEIDPattern OBJECT IDENTIFIER ::= { id-on ON-TBA } -- Encoding allows URI reserved characters BundleEIDPattern ::= UTF8String END

Examples

IPN Patterns This section contains examples specific to the IPN pattern of .

Exact Match This trivial example matches only one EID (which itself has the same text and CBOR forms) ipn:0.3.4 which has a CBOR form of: [[2, [0, 3, 4]]]

Wildcards This example matches all service numbers on a single node ipn:0.3.* which has a CBOR form of: [[2, [0, 3, true]]] This example matches all default-authority nodes with the same service number ipn:0.*.4 which has a CBOR form of: [[2, [0, true, 4]]]

Range Match This example includes a single range over the service numbers ipn:0.3.0 to ipn:0.3.19 inclusive as ipn:0.3.[0-19] which has a CBOR form of: [[2, [0, 3, [0, 20]]]] This example includes an offset range over the service numbers ipn:0.3.10 to ipn:0.3.19 inclusive as ipn:0.3.[10-19] which has a CBOR form of: [[2, [0, 3, [10, 10]]]] This example includes multiple ranges of service numbers ipn:0.3.0 to ipn:0.3.4 and ipn:0.3.10 to ipn:0.3.19 inclusive as ipn:0.3.[0-4,10-19] which has a CBOR form of: [[2, [0, 3, [0, 5, 5, 10]]]]

Normalization and Canonicalization These examples show normalization (altering the value while retaining its meaning) and canonicalization (altering the encoded form of the value). An overlapping or contiguous pattern such as one of the following ipn:0.3.[0-9,10-19] ipn:0.3.[0-15,10-19] ipn:0.3.[10-19,0-9] can be normalized to the equivalent pattern ipn:0.3.[0-19] An unordered pattern such as ipn:0.3.[10-19,0-4] can be normalized to the equivalent pattern ipn:0.3.[0-4,10-19] A pattern where a range covers the same component set as a wildcard would, as in ipn:977000.[0-4294967295].* can be identified and normalized to the equivalent pattern ipn:977000.*.* When the FQNN is not a range and indicates the LocalNode as in either of the following ipn:4294967295.[0-10] ipn:0.4294967295.[0-10] it can be canonicalized to the equivalent always-two-component pattern (in text form only) ipn:!.[0-10] When an interval has descending bounds such as ipn:0.3.[10-0] can be canonicalized to the equivalent pattern ipn:0.3.[0-10] When the end of an interval is the largest value of the corresponding component, as in ipn:977000.[10000-4294967295].* the last value of the last interval can be canonicalized to the pattern ipn:977000.[10000+].* which does not affect the information model but makes the encoded form shorter (and more understandable to a human).

Two-Component Text Form This example includes a range over the FQNN in a two-component form between ipn:4196183048192100.* to ipn:4196183048192500.* inclusive as as the pattern ipn:[4196183048192100-4196183048192500].* which is decomposed into the equivalent three-component pattern ipn:977000.[100-500].* which has a CBOR form of: [[2, [977000, [100, 401], true]]] The next example has a range over the FQNN which spans multiple allocator IDs between ipn:4196183048192100.* to ipn:4196191638126692.* inclusive as the pattern ipn:[4196183048192100-4196191638126692].* which is decomposed into one possible equivalent pattern ipn:977000.[100+].*|ipn:977001.*.*|ipn:977002.[0-100].* which has a CBOR form of: [ [2, [977000, [100, null], true]], [2, [977001, true, true]], [2, [977002, [0, 101], true]] ] As can be seen in that example, because the FQNN interval does not need to neatly align with the per-allocator node number intervals, the general case equivalent pattern will need to include multiple pattern items. The equivalent pattern also makes use of the wildcard node number in the second item to simplify matching and reduce encoded size when the FQNN interval covers all node numbers within an allocator.

Combined Patterns This section contains examples of patterns combining items.

Any-Scheme Match This trivial example matches any possible EID. It's text form is: *:** and its CBOR form is: true

Any-SSP Match These two examples match any ipn-scheme EID, either as text scheme or integer respectively: ipn:** and 2:** and both have a CBOR form of: [2]

Multiple Scheme Match This example combines items with different schemes together in one pattern, it will match dtn:** and ipn:0.3.4 It's text form is: dtn:**|ipn:0.3.4 and its CBOR form is: [ 1, [2, [0, 3, 4]] ]

Implementation Status [NOTE to the RFC Editor: please remove this section before publication, as well as the reference to , .] This section records the status of known implementations of the protocol defined by this specification at the time of posting of this Internet-Draft, and is based on a proposal described in . The description of implementations in this section is intended to assist the IETF in its decision processes in progressing drafts to RFCs. Please note that the listing of any individual implementation here does not imply endorsement by the IETF. Furthermore, no effort has been spent to verify the information presented here that was supplied by IETF contributors. This is not intended as, and must not be construed to be, a catalog of available implementations or their features. Readers are advised to note that other implementations can exist. A trial implementation in Rust language of the EID Pattern encoding and decoding and EID matching logic is present as part of the full BP Agent of . This repository includes unit test vectors for verifying pattern handling.

Acknowledgments Pattern expressiveness is based on use case examples provided by Carlo Caini and Lucien Loiseau. Prototyping of and validation for the utility of these patterns was performed by Rick Taylor.